zyxel P-2812HNU-F1 errors out on bad crc for trunk after installing through Luci
Username: Mafketel
Origin: https://bugs.openwrt.org/index.php?do=details&task_id=2124
Supply the following if possible:
- Device problem occurs on
zyxel P-2812HNU-F1
- Software versions of OpenWrt/LEDE release, packages, etc.
trunk
- Steps to reproduce
flash trunk firmware to modem via Luci, see below for output.
I have tried both with keep settings and with delete settings same error
serial console output
ROM VER: 1.0.5 CFG 06 NAND NAND Read OK
U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) SPL: initializing NAND flash SPL: checking U-Boot image SPL: loading U-Boot to RAM SPL: decompressing U-Boot with LZO SPL: jumping to U-Boot
U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx
Board: ZyXEL P-2812HNU-Fx SoC: Lantiq VRX288 v1.1 CPU: 500 MHz IO: 250 MHz BUS: 250 MHz BOOT: NAND DRAM: 128 MiB NAND: 128 MiB In: serial Out: serial Err: serial Net: ltq-eth Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x60000, size 0x200000 2097152 bytes read: OK
Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.98 Created: 2019-02-13 9:37:36 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2119245 Bytes = 2 MiB Load Address: 80002000 Entry Point: 80002000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! P-2812HNU-Fx #
serial console output flash proces
Watchdog handover: fd=3
- watchdog - killall: dropbear: no process killed killall: ash: no process killed Sending TERM to remaining processes ... logd rpcd netifd odhcpd vdsl_cpe_contro ntpd dnsmasq sh sysupgrade ubus ubusd askfirst Sending KILL to remaining processes ... Unlocking kernel ...
Writing from to kernel ... [e]Failed to get erase block status removing ubiblock0_0 [ 103.424000] UBI: ubiblock0_0 released Volume ID 0, size 23 LEBs (2967552 bytes, 2.8 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs", alignment 1 Set volume size to 123604992 Volume ID 1, size 958 LEBs (123604992 bytes, 117.9 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs_data", alignment 1 sysupgrade successful [ 104.356000] reboot: Reÿ ROM VER: 1.0.5 CFG 06 NAND NAND Read OK
U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) SPL: initializing NAND flash SPL: checking U-Boot image SPL: loading U-Boot to RAM SPL: decompressing U-Boot with LZO SPL: jumping to U-Boot
U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx
Board: ZyXEL P-2812HNU-Fx SoC: Lantiq VRX288 v1.1 CPU: 500 MHz IO: 250 MHz BUS: 250 MHz BOOT: NAND DRAM: 128 MiB NAND: 128 MiB In: serial Out: serial Err: serial Net: ltq-eth Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x60000, size 0x200000 2097152 bytes read: OK
Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.98 Created: 2019-02-13 9:37:36 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2119245 Bytes = 2 MiB Load Address: 80002000 Entry Point: 80002000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! P-2812HNU-Fx #